X32 CORE: Select Knob Functions

From behringerwiki
Jump to: navigation, search

The SELECT knob serves several functions on the X32 CORE. The following table describes the SELECT knob behavior in each of the available scenarios.


Channel Select Mode (SCENE/SETUP button LED is off)

Display

  • Selected channel number
  • Input source
  • Channel icon and color
  • Nickname


Short press

Toggles the selected channel to SOLO on/off

  • Channel signal will be sent to Monitoring L/R outputs on rear panel and Phones output on front panel
  • Exact behavior depends on settings in Monitoring page (remote controlled via editing software)


Rotate

Immediately selects the desired channel

(input, aux in, FX return, bus, matrix, main or DCA)

  • The Channel Type LEDs [5] will follow the selection.
  • Note that the X32 CORE Channel Selector will skip all channels, setting the display color to ’black’ or ’off’.


Long press

Clears all active channel solos


Scene Select Mode (accessed by pressing the SCENE/SETUP button so that the LED is green)

Display

  • “Scene” in bold
  • Current scene number
  • Next scene number and name (small) to be loaded on GO


Short press

Recalls the selected Scene from X32 internal memory “GO”

  • behavior depends on Scene settings/preferences (remote controlled via editing software)
  • Scene safes can only be set/reset remotely
  • Scenes/Shows from USB drives can only be accessed remotely
  • A complete show can be loaded from an attached USB drive into the internal memory using Setup Mode


Rotate

Preselects the next Scene


Setup Mode (accessed by pressing and holding the SCENE/SETUP button so that the LED is green)

Rotate and press

Select and enter the Setup pages:

1. Load Show

2. Contrast

3. LEDs

4. Clock Rate

5. Sync

6. IP Address

7. IP (Subnet) Mask

8. IP Gateway

9. Lock


1. Load Show

Load show from root directory of attached USB drive

  • display 3 rows:
  - Load Show
  - Exit
  - Show Files
  • Exit leads back to Setup Mode root level
  • Turn clockwise to scroll through a list of show fi les found in USB root directory, push to load selected show and return to Setup Mode root level


2. Contrast

LCD contrast

  • Rotate to adjust 0-100
  • Press to confi rm and exit


3. LEDs

LED brightness

  • Rotate to adjust 0-100
  • Press to confirm and exit


4. Clock Rate

Select the internal Sample Clock Rate

  • Rotate to adjust 44.1 or 48 kHz (change requires to reboot the X32 CORE)
  • Press to confirm and exit


5. Sync

Choose Clock Synchronization source

  • Rotate to select INT (internal), AES50 (Port) A, or AES50 (Port) B
  • Press to confirm and exit


6. IP Address

Select the IP Address for X32 CORE

  • Rotate to adjust the first triplet (0-255)
  • Press to confi rm
  • Rotate to adjust the second triplet (0-255)
  • Press to confi rm
  • Rotate to adjust the third triplet (0-255)
  • Press to confi rm
  • Rotate to adjust the fourth triplet (0-255)
  • Press to confi rm and exit


7. IP Mask

Select the IP Subnet Mask for X32 CORE

  • Rotate to adjust the first triplet (0-255)
  • Press to confirm
  • Rotate to adjust the second triplet (0-255)
  • Press to confirm
  • Rotate to adjust the third triplet (0-255)
  • Press to confirm
  • Rotate to adjust the fourth triplet (0-255)
  • Press to confirm and exit


8. IP Gateway

Select the IP Gateway for X32 CORE

  • Rotate to adjust the first triplet (0-255)
  • Press to confirm
  • Rotate to adjust the second triplet (0-255)
  • Press to confirm
  • Rotate to adjust the third triplet (0-255)
  • Press to confirm
  • Rotate to adjust the fourth triplet (0-255)
  • Press to confirm and exit


9. Lock

Locks the X32 CORE


  • Display “Lock Cancel”
  • Press to cancel locking
  • Rotating clockwise turns the display from Green to Red backlight and shows “LOCKED”
  • Press and hold the SCENE/SETUP button for 5 seconds in order to exit Locked mode and get back to the standard Channel Select mode (showing the last selected channel)